Once the engine is running, disengage the choke. Thrown object hazard—keep bystanders away. Squeeze the lever to engage the impeller. Installing the Chute. Figure 4. Figure 5. Installing the Traction-Control Linkage.
Figure 6. Installing the Chute-Control Rod. Figure 7. Installing the Snow-Cleanout Tool. Figure 8. Checking the Engine-Oil Level. Refer to Checking the Engine-Oil Level. Checking and Adjusting the Tire Pressure. Figure 9. Checking the Skids and Scraper. Checking the Operation of the Traction Drive. Carefully check the traction drive and adjust it properly, if necessary.
Figure Product Overview. Figure 13 Snow-cleanout tool attached to the handle. Before Operation. Before Operation Safety. Adjust the collector housing height to clear a gravel or crushed-rock surface. Fuel Safety. Do not handle fuel when smoking or around an open flame or sparks. Store fuel in an approved fuel container, out of the reach of children. When fuel is in the tank, tip the machine only as directed in the instructions. If you spill fuel on your clothing, change your clothing immediately.
Filling the Fuel Tank. During Operation. During Operation Safety. Never direct the discharge toward people or areas where property damage can occur. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run. Exercise extreme caution when operating the machine on a slope.
Do not operate the machine without good visibility or light. Look behind and use care when backing up the machine. When not actively clearing snow, disengage power to the auger.
Do not run the engine indoors; exhaust fumes are dangerous. Do not overload the machine capacity by attempting to clear snow at too fast a rate. Disengage all clutches and shift into neutral before starting the engine. Never operate the machine at high transport speeds on slippery surfaces.
Starting the Engine. Using Electric Start. The electrical cord can become damaged, causing a shock or fire. Using Recoil Start. Shutting Off the Engine. Operating the Traction Drive. Operating the Speed Selector. Do not operate the machine. Take it to an Authorized Service Dealer for service. Moving the Discharge Chute. Moving the Chute Deflector. Clearing a Clogged Discharge Chute. Never use your hands to clear a clogged discharge chute.
This could result in personal injury. Operating Tips. Keep the area to be cleared free of all objects that the auger could pick up and throw. Keep all children and pets away from the area of operation. After Operation. After Operation Safety. Preventing Freeze-up after Use. Recommended Maintenance Schedule s. Maintenance Service Interval Maintenance Procedure After the first 2 hours Inspect the traction cable and adjust it if necessary.
After the first 5 hours Change the engine oil. Before each use or daily Check the engine-oil level and add oil if necessary. Every 50 hours Change the engine oil.
Change the engine oil every 25 operating hours when operating the engine under a heavy load. Every hours Replace the spark plug. Yearly Check the skids and scraper and adjust them if necessary. Inspect the traction cable and adjust or replace it if necessary. Check the auger-gearbox oil and add oil if necessary.
Lubricate the hex shaft. Yearly or before storage Check the air pressure in the tires and inflate them to to kPa 17 to 20 psi. Run the engine to dry out the fuel tank and the carburetor at the end of the season. Maintenance Safety. Do not change the governor settings on the engine. Purchase only genuine Toro replacement parts and accessories. Preparing for Maintenance. Move the machine to a level surface. Shut off the engine and wait for all moving parts to stop.
Maintenance Service Interval Maintenance Procedure Before each use or daily Check the engine-oil level and add oil if necessary. Checking and Adjusting the Skids and Scraper. Figure 25 1. Checking and Adjusting the Traction Cable.
Yearly Inspect the traction cable and adjust or replace it if necessary. Figure 27 Jam nut Turnbuckle. Figure 29 1. Figure 30 Jam nut Turnbuckle. Checking the Auger-Gearbox-Oil Level. Changing the Engine Oil. Figure 33 Oil-drain cap. Lubricating the Hex Shaft. Figure 35 Hex shaft Aluminum friction plate Rubber wheel. Figure 36 Back cover. Replacing the Spark Plug. Replacing the spark plug while the engine is hot can result in burns.
Wait until the engine is cool to replace the spark plug. Figure 37 Spark-plug boot. Figure 39 0. Replacing the Drive Belts. Replacing the Headlight. Replace the headlight assembly Toro part number when needed. Storage Safety. Storing the Machine. Run the engine for 10 minutes to distribute the conditioned fuel through the fuel system. Run the machine until the engine runs out of fuel.
Prime the engine and start it again. Allow the engine to cool. Remove the key. Clean the machine thoroughly. Tighten all loose screws, bolts, and locknuts. Repair or replace any damaged parts. Cover the machine and store it in a clean, dry place out of the reach of children. Removing the Machine from Storage. Problem Possible Cause Corrective Action The electric starter does not turn electric-start models only. The snow blower shovel uses no gas or electricity and is equipped with a snowblower auger on it that auto-rotate as you push the shovel along the ground and then pushes the snow to the side of the shovel as you walk.
My only worry is that the further you get along, the more snow is going to start piling up and will start making it harder and harder to get through. But I guess it still beats a shovel. The manual hand powered snow blower shovel is made using sturdy, weatherproof, and unbreakable plastic, has a double handle for a more comfortable grip which also folds down for easy storage, and is very lightweight and easy to use.
The Manual Snow Shovel With Auger does require a little bit of assembly, however, its simple design makes it easy to put together. All you need to do is push!
Make a tough job simple with this manual snow plow! The snowblower is made Sturdy and weatherproof, manufactured from unbreakable plastic for durability and flexibility. Its blade and auger are constructed from durable, impact and corrosion-resistant plastic. The handlebar is made from powder-coated metal that has an ergonomic plastic grip.
For easy push, it is equipped with a double handle for a more comfortable and powerful push. The handles are foldable for easy storage and conveniently lightweight. Make the most out of your kitchen countertop by investing in an Expandable Kitchen Pan Organizer. It offers a practical way to eliminate clutter in a small kitchen.
The best part? It can be expanded to accommodate up to eight pans with ease. A part from the hair advantages it has, it is durable. This premium quality knife set has a razor sharp edge with an octagonal metal handle for a firm grip. Each knife is made with ingenious craftmanship that creates the unique ripple pattern running through each blade. Perfect for everyday use.
0コメント